White Cat lighting board

White Cat Lighting Board Documentation

Outils pour utilisateurs

Outils du site


configuration_network_eng

Différences

Ci-dessous, les différences entre deux révisions de la page.

Lien vers cette vue comparative

Both sides previous revision Révision précédente
configuration_network_eng [2013/07/06 15:53]
christoph
configuration_network_eng [2014/11/29 21:59] (Version actuelle)
174.61.171.90
Ligne 9: Ligne 9:
  
 ====IP ROUTING==== ====IP ROUTING====
 +
 This list allows you to see which adapters are connected to a network. This list allows you to see which adapters are connected to a network.
 +
 To the left of each is the IP address that White Cat can use: To the left of each is the IP address that White Cat can use:
-    ​* to receive Artnet + 
-    * to send Artnet +  ​* to receive Artnet 
-    * for communication with iCat+  * to send Artnet 
 +  * for communication with iCat 
 You can have three types of communication on separate cards or on the same card. You can have three types of communication on separate cards or on the same card.
  
 ====ArtNet==== ====ArtNet====
 +
 +**Attention**
 +
 As already mentioned in the DMX configuration section, you will have already entered the IP address of your Enttec Ode or other Artnet interface box and the subnet and universe that it transmits on (usually 0-0). As already mentioned in the DMX configuration section, you will have already entered the IP address of your Enttec Ode or other Artnet interface box and the subnet and universe that it transmits on (usually 0-0).
  
-Warning: +You can connect/​disconnect ​on the fly to the network card of your choice ​(wifi/​RJ45/​RJ45 adapters PCMCIA).
-So be sure that you have a network adapter set to that IP family ​on your machine. The DMX Configuration tab indicates where to send the data (ie the IP of the Ode or other Artnet interface box). It does not define by what route the data will be sent. That is the IP routing, which is on the Network tab as shown above.+
  
-You can connect/​disconnect the fly to the network adapter of your choice (WiFi/RJ45 and PCMCIA/​USB). 
 When you connect to a network adapter on this menu, you can receive an Artnet signal from this IP card and from this IP family. When you connect to a network adapter on this menu, you can receive an Artnet signal from this IP card and from this IP family.
  
 For the Artnet program to work, it is necessary that the Artnet IP defined in the configuration (CFG DMX) be in the same IP family as the one White Cat is logged onto (eg if the Artnet signal is sent to 192.168.1.50,​ then you should be connected to a network adapter with an IP of 192.168.1.X). For the Artnet program to work, it is necessary that the Artnet IP defined in the configuration (CFG DMX) be in the same IP family as the one White Cat is logged onto (eg if the Artnet signal is sent to 192.168.1.50,​ then you should be connected to a network adapter with an IP of 192.168.1.X).
 +
 ===UDP ports=== ===UDP ports===
 +
 Default UDP port is ArtNet port 6454. DMX interfaces, and most of their software transmit or receive information through this port. For example, if the OUT port for White Cat is not 6454, then the ENTTEC ODE will receive nothing as it listens to the port (6454) specified by the Artnet protocol. Default UDP port is ArtNet port 6454. DMX interfaces, and most of their software transmit or receive information through this port. For example, if the OUT port for White Cat is not 6454, then the ENTTEC ODE will receive nothing as it listens to the port (6454) specified by the Artnet protocol.
  
Ligne 33: Ligne 40:
 Control is taken by these applications. ​ As with a USB port, if you connect your dmx interface that you use with White Cat, and you try to start Schwarztpeter,​ it will not work. White Cat has taken control. A port IN> one application,​ OUT port> one application. Control is taken by these applications. ​ As with a USB port, if you connect your dmx interface that you use with White Cat, and you try to start Schwarztpeter,​ it will not work. White Cat has taken control. A port IN> one application,​ OUT port> one application.
  
-If you open a software program like VVVV with a DMX node (Arnet receiver) and then you open White Cat with server mode enabled (ON receiving ​Art-Net), the VVVV node will disappear because White Cat takes over the UDP port IN.+If you open a software program like VVVV with a DMX node (Artnet ​receiver) and then you open White Cat with server mode enabled (ON receiving ​Artnet), the VVVV node will disappear because White Cat takes over the UDP port IN.
  
 This problem with ports was resolved on the ChamSys MagicQ software by letting you specify on what port to transmit and what port to receive, thus allowing the coexistence of several Artnet applications on the same machine (ie 6454 to send and 6453 to receive). This problem with ports was resolved on the ChamSys MagicQ software by letting you specify on what port to transmit and what port to receive, thus allowing the coexistence of several Artnet applications on the same machine (ie 6454 to send and 6453 to receive).
 +
 ===Assignment to the dock ArtNet In=== ===Assignment to the dock ArtNet In===
-You can receive up to 4 universes of ArtNet ​in White Cat.+ 
 +You can receive up to 4 universes of Artnet ​in White Cat. 
 This choice is made from the sixteen universes of subnet 0 numbered 0-15. This choice is made from the sixteen universes of subnet 0 numbered 0-15.
-To assign an ArtNet ​universe to a dock:+ 
 +To assign an Artnet ​universe to a dock: 
   - type the number of the universe (0-15)   - type the number of the universe (0-15)
   - click [Affect to dock]   - click [Affect to dock]
   - click the dock to which you want to assign this dynamic content   - click the dock to which you want to assign this dynamic content
-  - set ArtNet ​IN to ON. This will open the ArtNet ​server on the specified port+  - set Artnet ​IN to ON. This will open the Artnet ​server on the specified port 
 When you quit White Cat, the most recent configuration is saved, so that it is re-opened at startup. When you quit White Cat, the most recent configuration is saved, so that it is re-opened at startup.
  
 ====Fantastick iCat Builder==== ====Fantastick iCat Builder====
 +
 Remote iPhone/​iPad:​ here you define what address to send the data to fantastick and which UDP ports to use. Remote iPhone/​iPad:​ here you define what address to send the data to fantastick and which UDP ports to use.
 See Fantastick-iCat See Fantastick-iCat
configuration_network_eng.txt · Dernière modification: 2014/11/29 21:59 par 174.61.171.90